TP-LINK TD-8817 Uživatelský manuál

TD-8817 ADSL2/2+ Ethernet/USB Router Rev：1.0.0

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 4Method two：Restore the default setting from “Maintenance-SysRestart” of the Router's Web-based

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 5 Figure 2-3

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 6 Chapter 3. Quick Installation Guide 3.1 Configure PC After you directly connect your PC to the T

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 7 Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the P

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 8Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK. Figure 3-4 ) Note: Yo

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 9If the result displayed is similar to the screen shown below, it means that your PC has not connect

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 10 Figure 3-7 Step 3: You will see Figure 3-8 as follow, please wait a moment. Figure 3-8 Step

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 11 Figure 3-9 ) Note: 1) All of the above settings are under windows XP. 2) If you want to pull

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 12 Figure 3-10 Step 1: Select the Quick Start tab, then click RUN WIZARD, and you will see Figure 3

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 13 Figure 3-13 Step 4: Select the connection type to connect to the ISP (We select PPPoE/PPPoA mode

COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 14) Note: In Quick Start, you shouldn’t configure the PVC which uses the same VPI/VCI as the seven d

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 15 Chapter 4. Software Configuration This User Guide recommends using the “Quick Installation Guid

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 16 Figure 4-2 ) Note: Click the other submenus System Log or Statistics in Figure 4-2, you will be a

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 174.3.1 Internet Choose “Interface Setup→Internet” menu, you can configure the parameters for WAN po

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 18• Status: If you want to use a designed VC, you should activate it. • VPI: Identifies the virtua

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 19RIP-2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast format.

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 20 Figure 4-7 ¾ Username: Enter your username for your PPPoE/PPPoA connection. ¾ Password: Enter y

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 21If you select this type of connection, the modem can be configured to act as a bridging device bet

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 22• IP Address: Enter the Router’s local IP Address, then you can access to the Web-based Utility v

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 23expired, the user will be automatically assigned a new dynamic IP address. The default is 259200 s

FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 24 4.4 Advanced Setup Choose “Advanced Setup”, you can see the next submenus: Figure 4-12 Click any

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 25 Figure 4-14 Click ADD ROUTE button to add a new route in the next screen (shown in Figure 4-15).

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 26 Figure 4-16 ¾ Virtual Circuit: Enter Virtual Circuit Index that you plan to setup for the NAT fu

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 27The Virtual Server is the server or server(s) behind NAT (on the LAN), for example, Web server or

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 284.4.3.3. IP Address Mapping Choose “Advanced Setup→NAT”, select Multiple in Number of IPs. Click

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 29To add a mapping rule: Step 1: Select the “Virtual Circuit” and Multiple for the “Number of IPs

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 30 Figure 4-21 ¾ QoS: Select this option to Activate/Deactivate the IP QoS on different types (IP T

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 31• Protocol ID: Select one among TCP/UDP, TCP, UDP or ICMP protocols for the application. • Vlan

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 32 Figure 4-22 1. Assign VLAN PVID for each Interface Click Assign VLAN PVID for each Interface in

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 33 Figure 4-24 ¾ VLAN Index: Select the VLAN index for this VC. You can specify 8 groups in maximum

Package contents The following contents should be found in your box: ¾ One TD-8817 ADSL2/2+ Ethernet/USB Router ¾ One AC power Adapter for TD-88

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 34 Figure 4-25 ¾ ADSL Mode: Select the ADSL operation mode which your ADSL connection uses. ¾ ADSL

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 35 Figure 4-27 ¾ ACL: If Activated, the IP addresses which are contained in the Access Control Li

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 36 Figure 4-28 ¾ Filter Type Selection: Select the filter type for the configuration below. ¾ IP

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 37Incoming means that IP traffic which is coming into the router, and the Outgoing means that IP tra

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 38 ) Note: If you want to make the rule take effect, please select Yes to active the rule. Step 3:

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 394.5.2.2. MAC Filter Select IP/Mac Filter as the Filter type, and select MAC as the Rule type (show

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 40Select the “MAC” as the Rule Type on the Filter screen (show in Figure 4-29). , Then you can confi

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 41 Figure 4-30 ¾ Filter Type Selection: Select the Application Filter for the next configuration. ¾

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 42 Figure 4-31 ¾ Filter Type Selection: Select the URL Filter for the next configuration. ¾ Active

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 434.5.3 SNMP Choose “Access Management→SNMP”, you can see the SNMP screen. The Simple Network Manage

CONTENT Chapter 1. Introduction ... 1 1.1 Product Overview...

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 444.5.5 DDNS Choose “Access Management→DDNS”, you can configure the DDNS function in the screen (sho

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 45 Figure 4-35 ¾ CWMP: Select activate the CWMP function. ¾ URL: Enter the website of ACS which is

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 46 Figure 4-37 ) Note: 1) There is only one account that can access Web-Management interface. The d

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 47) Note: The ADSL Router built-in some NTP Servers, when the Router connects to the Internet, the R

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 48to be used for upgrade. Figure 4-41 To upgrade the router's firmware, follow these instructi

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 49 Figure 4-42 Step 2: Save the file as the appointed file (shown in Figure 4-43). Figure 4-43 To

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 50 Figure 4-44 4.6.5 Diagnostic Choose “Maintenance→Diagnostic”, you can view the test results for t

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 51 Figure 4-46 ) Note: Click the tab, and you will be able to get the corresponding information.

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 52 Appendix A: Specification General Standards and Protocols ANSI T1.413, ITU G.992.1, ITU G.992.2,

4.6.3 Firmware...47 4.6.4 Sy

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 1 Chapter 1. Introduction 1.1 Product Overview Thank you for choosing the TD-8817 ADSL2/2+ Etherne

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 2¾ Built-in firewall, supports IP/MAC filter, Application filter and URL filter. ¾ Supports Virtua

TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 3 Chapter 2. Hardware Installation 2.1 The Front Panel Figure 2-1 The LEDs are located on the fr