Tp-link TL-SG3109 Uživatelský manuál

TL-SG3109Embedded Web System User GuideTL-SL34289-port Gigabit Managed Switch24+4G Gigabit Managed SwitchTL-SL345248+4G Gigabit Managed SwitchRev: 1.

23Section 1. Getting StartedThis section provides an introduction to the user interface, and includes the following topics: Conguring the device to

9293Section 15. Viewing StatisticsThis section describes how to view and manage device statistics for interfaces, GVRP, EAP, and Etherlike and how to

9495Packets with Errors — Displays the number of error packets received from the selected interface.Transmit StatisticsTotal Bytes (Octets) — Displays

9495To update the refresh time:To change the refresh rate for statistics, select another rate from the Refresh Rate dropdown list.To reset Etherlike i

96971. Open the GVRP Statistics Page.2. Click . The GVRP interface statistics counters are cleared.15.1.4 Viewing EAP StatisticsThe EAP Statist

9697Conguring RMON HistoryDening RMON Alarms15.2.1 Viewing RMON StatisticsThe RMON Statistics Page contains elds for viewing information about de

9899Frames of xx Bytes — Number of xx-byte frames received on the interface since the device was last refreshed.2. Select an interface (Port or LAG)

9899Figure 138: Add History Entry User Page 3. Dene the elds.4. Click . The entry is added to the RMON Histo

100101the device was last refreshed.Oversize Packets — Displays the number of oversized packets (over 1518 octets) received on the interface since the

100101Figure 142: Add RMON Event User Page 3. Dene the elds.4. Click . The entry is added to the RMON Even

102103Interface — Displays interface for which RMON statistics are displayed. The possible eld values are:– Port — Displays the RMON statistics for t

45To access the TP-Link user interface:1. Open an Internet browser.2. Ensure that pop-up blockers are disabled. If pop-up blockers are enable, mod

102103Figure 147: Edit RMON Alarm User Page 2. Modify the elds.3. Click . The entry is updated in the RMON Al

104105GlossaryThis glossary contains terms commonly used in Embedded Web System documentation.Term DenitionAAccess Mode Species the method by which

104105Term DenitionBackplane The main BUS that carries information in the device.BandwidthSpecies the amount of data that can be transmitted in a x

106107Term DenitionCLI Command Line Interface. A set of line commands used to congure the system.ClientA computer system or process that requires se

106107Term DenitionEthernetUses a bus or star topology and supports data transfer rates of Mpbs. A newer version called Fast Ethernet supports 100 Mb

108109Term DenitionIIADIntegrated Access Device. Device that multiplexes varied communication technologies onto a single telephone line for transmiss

108109Term DenitionL2TPLayer 2 Tunnel Protocol. Helps build virtual private networks in the dial access space, and provides Layer 2 Forwarding L2F) p

110111Term DenitionNMSNetwork Management System. An interface that provides a method of managing a system.NodeA network connection endpoint or a comm

110111Term DenitionRedundancyProvides duplication of devices, services, or events. If a device, service, or event fails, redundancy provides a backup

112Term DenitionSubnet MaskUsed to mask all or part of an IP address used in a subnet address. Switch Filters and forwards packets between LAN segmen

45This section provides the following additional information:Device Representation — Provides an explanation of the TP-Link user interface buttons, in

11271035590TP-LINK TECHNOLOGIES CO., LTD.E-mail: [email protected]: http://www.tp-link.comAdd: 3/F., Building R1-B, Hi-tech Industrial Park,

671.4 Using Screen and Table OptionsThe TP-Link Embedded Web Interface contains screens and tables for configuring devices. This section contains the

67Figure 6: IP Addressing Page 2. Select the Remove checkbox in the row of the item to dele

89Section 2. Dening Device Information This section contains information for viewing and setting general system information.The System Description P

89Section 3. Setting the System TimeThis section provides information for conguring system time parameters, including:Conguring Daylight Savings Ti

1011Latvia — From the last weekend of March until the last weekend of October.Lebanon — From the last weekend of March until the last weekend of Octob

1011The DST can be set according to unique start and end dates for a particular year or as a recurring period for any year. For a specic setting in a

12134. Click . The DST settings are saved, and the device is updated.3.2 Conguring SNTPThis section contains the following topics: SNTP Overview

COPYRIGHT & TRADEMARKSSpecications are subject to change without notice. is a registered trademark of TP-LINK Technologies Co., Ltd. Other bra

1213server, the SNTP client listens for the response. The SNTP client neither sends time information requests nor receives responses from the Broadcas

1415To congure SNTP authentication: 1. Click System > System Info > SNTP > Authentication. The SNTP Authentication Page opens: Figure 13:

1415Figure 15: SNTP Servers Page The SNTP Servers Page contains the following elds:SNTP Server

1617Figure 17: SNTP Interface Settings Page The SNTP Interface Settings Page contains the following elds:Interfa

1617Section 4. Conguring System LogsThis section provides information for managing system logs. The system logs enable viewing device events in real

1819Figure 19: Syslog Properties Page The Syslog Properties Page contains the following elds: Enable L

1819To view Flash memory logs: 1. Click System > System Info > Syslog > Flash. The Syslog Flash Page opens: Figure 21: Syslog Flash Page

2021Figure 23: Add Syslog Server Page 3. Dene the IP Address, UDP Port, Facility, Description, and Min

2021Section 5. Conguring Device SecurityThis section describes pages that contain fields for setting security parameters for ports, device managemen

2223Figure 24: Access Prole Page The Access Prole Page contains the following elds:Access Pro

TABLE OF CONTENTSPreface ... 1Guide Overvi

2223– Prex Length — Denes the number of bits that comprise the source IP address prex, or the network mask of the source IP address.Action —Denes

2425Prex Length — Denes the number of bits that comprise the source IP address prex, or the network mask of the source IP address.Action — Denes t

2425Each of the tables contains the following elds: Prole Name — Contains a list of user-dened authentication prole lists to which user-dened aut

2627Figure 32: Authentication Mapping Page The Authentication Mapping Page contains the following elds: Console

2627session is permitted.2. Dene the Console, Telnet, and Secure Telnet (SSH) elds. 3. Map the authentication method in the Secure HTTP se

2829Timeout for Reply — Denes the amount of time in seconds that passes before the connection between the device and the TACACS+ times out. The eld

2829Figure 36: Radius Page The Default Parameters section of the Radius Page cont

30311. Click . The RADIUS Server Settings Page opens: Figure 38: RADIUS Server Settings Page2. Modify the elds. 3. Click . The RAD

30315.1.2.2 Dening Line PasswordsNetwork administrators can define line passwords in the Line Password Page. After the line password is defined, a

3233Network Security OverviewDening Network Authentication PropertiesConguring Trafc Control5.2.1 Network Security OverviewThis section provides

4.3 Viewing Flash Logs ... 184.4 Defin

3233parameters. In addition, Guest VLANs are enabled from the Network Security Authentication Properties Page. To dene the network authentication pro

3435Current Port Control — Displays the current port authorization state. The possible eld values are:– Auto — Enables port-based authentication on t

3435Figure 46: Multiple Hosts Page The Multiple Hosts Page contains the following elds:Port — D

3637Figure 48: Authenticated Hosts Page The Authenticated Hosts Page contains the following elds:User Nam

3637Figure 49: Port Security Page The Port Security Page contains the following elds:Interfa

3839A Broadcast Storm is a result of an excessive amount of broadcast messages simultaneously transmitted across a network by a single port. Forwarded

3839Section 6. Dening IP AddressesThis section provides information for dening IP addresses on the device using DHCP and ARP. In addition, this sec

4041Figure 54: Add IP Interface Page 3. Define the IP Address, Network Mask, Prefix Length and Int

4041Figure 57: DHCP Page The DHCP Page contains the following elds:Interface —

4243IP Address - Indicates the station IP address, which is associated with the MAC address lled in below.MAC Address - Displays the station MAC addr

Section 7. Conguring Interfaces ... 457.1 Configuring Ports ...

4243eld values are:– Dynamic — The IP address is dynamically created.– Static — The IP address is a static IP address.Remove — Removes DNS servers. T

4445Figure 64: Add DNS Host Page 3. Enter the Host Name and IP Address.4. Click . The new DN

4445Section 7. Conguring InterfacesThis section contains the following topics:Conguring PortsConguring LAGsConguring VLANs7.1 Conguring PortsT

4647– 1000 Half — Indicates that the port advertises for a 1000 Mbps speed port and half duplex mode setting.Back Pressure — Displays the back pressur

46477.2 Conguring LAGsLink Aggregation optimizes port usage by linking a group of ports together to form a single LAG. Aggregating ports multiplies

4849Figure 68: LAG Membership Settings Page The LAG Membership Settings Page contains the following elds:LAG — Contai

4849Figure 70: LACP Parameters Settings Page 3. Dene the Port Priority and LACP Timeout settings.4. Click . The LA

5051Figure 71: VLAN Member Properties Page The VLAN Member Properties Page contains the following elds:Select VLAN

5051To dene VLAN membership:1. Click System > Bridging Config > VLAN >Membership > Membership. The VLAN Member Membership Page opens:Fi

5253disabled on an access port.– Trunk — Indicates the port belongs to VLANs in which all ports are tagged, except for one port that can be untagged.–

11.3.1 Defining SNMP Global Parameters ... 7111.3.2 Defining SNMP Vie

52531. Click System > Bridging Cong > VLAN > GARP. The GARP Parameters Page opens:Figure 77: GARP Parameters Page

5455Figure 79: GVRP Parameters Page The GVRP Parameters Page is divided into port and LAG parameters. T

5455Section 8. Dening the Forwarding DatabasePackets addressed to destinations stored in either the Static or Dynamic databases are immediately forw

56572. Click . The Add Forwarding Database Page opens:Figure 82: Add Forwarding Database Page3. Dene the Interface, MAC Add

56571. Click System > Bridging Config > Forwarding Database > Dynamic Addresses. The Dynamic Addresses Page opens.2. Select the Interface,

5859Section 9. Conguring the Spanning Tree ProtocolThe Spanning Tree Protocol (STP) provides tree topography for any arrangement of bridges. STP als

5859– Rapid STP — Enables Rapid STP on the device.– Multiple STP — Enables Multiple STP on the device.BPDU Handling — Determines how BPDU packets are

6061Figure 85: STP Interface Settings Page The STP Interface Settings Page contains the following elds:Interf

60619.2 Conguring the Rapid STPWhile Classic STP prevents Layer 2 forwarding loops in a general network topology, convergence can take between 30-6

6263Point-to-Point Operational Status — Displays the point-to-point operating state.LAG — Displays the LAG to which the interface is attached.2. Cli

13.4 Copying System Files ... 88Section 14. P

6263Figure 89: MSTP Properties Page The MSTP Properties Page contains the following elds:Region Nam

64653. Click . The MSTP settings are saved and the device is updated.9.3.3 Conguring MSTP VLAN InstancesNetwork Administrator can assign MSTP fo

6465The possible eld values are:– Root — Provides the lowest cost path to forward packets to the root device.– Designated — Indicates the port or LAG

6667Section 10. Conguring Multicast ForwardingMulticast forwarding enables transmitting packets from either a specic multicast group to a source, o

6667The default value is 300 seconds.Leave Timeout — Indicates the amount of time the host waits, after requesting to leave the IGMP group and not rec

6869Bridge Multicast Address — Identies the Multicast group MAC address/IP address.Port — Displays the port that can be added to a Multicast service.

686910.3 Dening Multicast Forward All ParametersThe Multicast Forward All Page contains elds for attaching ports or LAGs to a device that is attac

7071Section 11. Conguring SNMP ManagementSimple Network Management Protocol (SNMP) provides a method for managing network devices. The device suppor

7071Dening SNMP Group MembersDening SNMP Communities11.3.1 Dening SNMP Global ParametersThe SNMP Security Global Parameters Page permits the enab

7273SNMP view.Remove — Deletes the currently selected view. The possible eld values are:– Checked — Removes the selected view.– Unchecked — Maintains

1Preface The Embedded Web System (EWS) is a network management system. The TP-Link Embedded Web Interface congures, monitors, and troubleshoots netwo

72732. Click . The Add SNMP Group Prole Page opens:Figure 104: Add SNMP Group Prole Page 3. Dene the Group Na

7475– SHA Password — Users are authenticated using the HMAC-SHA-96 authentication level. The user should enter a password.– No Authentication — No use

747511.3.5 Dening SNMP CommunitiesAccess rights are managed by dening communities in the SNMP Communities Page. When the community names are chang

7677the device is updated.To modify SNMP Group Membership settings:1. Click System > SNMP Management > Security > Communities. The SNMP Com

76771. Click System > SNMP Management > Notication > Notication Filter. The SNMP Notication FiIter Page opens:Figure 113: SNMP Noticati

7879Figure 115: SNMP Notication Receiver Page The SNMP Notication Receiver Page c is divided into the following tables:S

7879– Unchecked — Maintains the list of recipients.2. Click . The Add SNMP Notication Receiver Page opens:Figure 116: Add SNMP Notication Receive

8081Section 12. Conguring Quality of ServiceThis section contains the following topics:Quality of Service OverviewEnabling Quality of ServiceMapping

8081The following table contains the VPT to Queue default settings:Table 7: VPT Default Mapping TableVPT Value Queue Number0 21 12 13 24 35 36 47 4Map

8283 Note:When moving to and from basic and advanced QoS modes, some settings may be lost.12.1.2.1 Basic QoS ModeBasic Mode supports activating

23Section 14. Performing Device Diagnostics — Provides information about port mirroring conguration, copper and ber cables testing, and viewing dev

8283Figure 118: CoS Settings Page The CoS Settings Page contains the following elds:Quality of

8485Figure 120: QoS Queue Settings Page The QoS Queue Settings Page contains the following elds:Queue — Indi

84851. Click System > Quality of Service > Queue Mapping > DSCP to Queue. The DSCP to Queue Page opens:Figure 122: DSCP to Queue Page

8687Section 13. Managing System FilesFile maintenance on the device includes conguration le management and device access. The conguration le stru

868713.1.2 Firmware DownloadThe Firmware Download section contains the following elds:TFTP Server IP Address — Species the address of the TFTP ser

888913.2.2 Software Image Upload The Software Image Upload section contains the following elds:TFTP Server IP Address — Species the address of the

8889Figure 126: Copy Files Page The Copy Files Page contains the following elds:Copy Conf

9091Section 14. Performing Device DiagnosticsThis section contains the following topics:Conguring Port MirroringViewing Integrated Cable TestsViewin

9091To modify port mirroring settings:1. Click . The Port Mirroring Settings Page opens.Figure 129: Port Mirroring Settings Page

929314.3 Viewing Optical TransceiversThe Optical Transceivers Page allows network managers to perform tests on ber-optic cables. Note:Optical t